Trending Topics

Implement and configure AWS Backup for VMware Cloud on AWS VM workloads

Image
In our previous post we saw the design of the AWS Backup on VMC. In this post we’re going through the implementation steps As per the design and best practice, we are going to use the ENI for the Backup traffic CREATE A VPC ENDPOINT  TO CREATE AN INTERFACE ENDPOINT FOR AN AWS SERVICE 1. Open the Amazon VPC console at https://console.aws.amazon.com/vpc    2. In the navigation pane, choose Endpoints 3. Choose Create endpoint 4. Name the endpoint   5. For Service category, choose AWS services 6. For Service name, search “ Backup ” and select “ backup-gateway ” service from the dropdown 7. For VPC, select the VPC which we used for SDDC deployment and extension 8. To create an interface endpoint for Amazon S3, you must “uncheck” Additional settings, Enable DNS name. This is because Amazon S3 does not support private DNS for interface VPC endpoints 9. For  Subnets , select one subnet per Availability Zone which we used for SDDC VMC selection  10. For Security group , sel

DHCP -Information




Ipconfig
Displays all current TCP/IP network configuration values and refreshes Dynamic Host Configuration Protocol (DHCP) and Domain Name System (DNS) settings. Used without parameters, ipconfig displays the IP address, subnet mask, and default gateway for all adapters.
Syntax
ipconfig [/all] [/renew [Adapter]] [/release [Adapter]] [/flushdns] [/displaydns] [/registerdns] [/showclassid Adapter] [/setclassid Adapter [ClassID]]
Top of page
Parameters
/all : Displays the full TCP/IP configuration for all adapters. Without this parameter, ipconfig displays only the IP address, subnet mask, and default gateway values for each adapter. Adapters can represent physical interfaces, such as installed network adapters, or logical interfaces, such as dial-up connections.
/renew [Adapter] : Renews DHCP configuration for all adapters (if an adapter is not specified) or for a specific adapter if the Adapter parameter is included. This parameter is available only on computers with adapters that are configured to obtain an IP address automatically. To specify an adapter name, type the adapter name that appears when you use ipconfig without parameters.
/release [Adapter] : Sends a DHCPRELEASE message to the DHCP server to release the current DHCP configuration and discard the IP address configuration for either all adapters (if an adapter is not specified) or for a specific adapter if the Adapter parameter is included. This parameter disables TCP/IP for adapters configured to obtain an IP address automatically. To specify an adapter name, type the adapter name that appears when you use ipconfig without parameters.
/flushdns : Flushes and resets the contents of the DNS client resolver cache. During DNS troubleshooting, you can use this procedure to discard negative cache entries from the cache, as well as any other entries that have been added dynamically.
/displaydns : Displays the contents of the DNS client resolver cache, which includes both entries preloaded from the local Hosts file and any recently obtained resource records for name queries resolved by the computer. The DNS Client service uses this information to resolve frequently queried names quickly, before querying its configured DNS servers.
/registerdns : Initiates manual dynamic registration for the DNS names and IP addresses that are configured at a computer. You can use this parameter to troubleshoot a failed DNS name registration or resolve a dynamic update problem between a client and the DNS server without rebooting the client computer. The DNS settings in the advanced properties of the TCP/IP protocol determine which names are registered in DNS.
/showclassid Adapter : Displays the DHCP class ID for a specified adapter. To see the DHCP class ID for all adapters, use the asterisk (*) wildcard character in place of Adapter. This parameter is available only on computers with adapters that are configured to obtain an IP address automatically.
/setclassid Adapter [ClassID] : Configures the DHCP class ID for a specified adapter. To set the DHCP class ID for all adapters, use the asterisk (*) wildcard character in place of Adapter. This parameter is available only on computers with adapters that are configured to obtain an IP address automatically. If a DHCP class ID is not specified, the current class ID is removed.
/?: Displays help at the command prompt.
Top of page
Remarks

The ipconfig command is the command-line equivalent to the winipcfg command, which is available in Windows Millennium Edition, Windows 98, and Windows 95. Although Windows XP does not include a graphical equivalent to the winipcfg command, you can use Network Connections to view and renew an IP address. To do this, open Network Connections, right-click a network connection, click Status, and then click the Support tab.

This command is most useful on computers that are configured to obtain an IP address automatically. This enables users to determine which TCP/IP configuration values have been configured by DHCP, Automatic Private IP Addressing (APIPA), or an alternate configuration.

If the Adapter name contains any spaces, use quotation marks around the adapter name (that is, "Adapter Name").

For adapter names, ipconfig supports the use of the asterisk (*) wildcard character to specify either adapters with names that begin with a specified string or adapters with names that contain a specified string. For example, Local* matches all adapters that start with the string Local and *Con* matches all adapters that contain the string Con.

This command is available only if the Internet Protocol (TCP/IP) protocol is installed as a component in the properties of a network adapter in Network Connections

Popular posts from this blog

HOW TO EDIT THE BCD REGISTRY FILE

DNS Scavenging.

AD LDS – Syncronizing AD LDS with Active Directory